When you try to set up your Netgear EX2700, it doesn’t recognize your WiFi connection. If that’s the case, you should give this post a read. In this article, you will discover how to troubleshoot the WiFi connection so that you may successfully setup Netgear extender Proceed with reading.
Fixed: Netgear EX2700 Not Detecting WiFi During Setup
When connected to a dual-band WiFi router, the Netgear EX2700 MU-MIMO range extender automatically searches for a 5 GHz WiFi network to utilize as a backhaul or uplink connection. The Netgear EX2700 should be able to detect the 5 GHz network by default, but if it isn’t, try the following solutions.
-
Move the EX2700 Extender
It is essential to first double-check where your Netgear EX2700 WiFi range extender is situated. If it’s too far away from your current router, try moving it closer. When deciding where to put your Netgear EX2700 MU-MIMO extender, keep the following in mind:
-
If at all feasible, keep the router and the extender in the same room.
-
If possible, put the extender in a spot with plenty of fresh air.
-
It’s not a good idea to store your range extender in a drawer, a cupboard, or beneath a table.
-
Your Netgear EX2700 range extender needs some breathing room from your other electronics, including your microwave, refrigerator, Bluetooth speakers, cordless phones, and baby monitors.
-
You shouldn’t put your extender near any water or reflective surfaces, such as mirrors, glasses, or fish tanks.
-
Keep your extender up high, on a shelf, if at all possible.
After relocating your extender, try to access the mywifiext net login page on your computer and see if the issue you were facing has been fixed or not.
-
Restart Your Extender
If you’re having problems with your Netgear EX2700 not recognizing WiFi during setup, try rebooting it as suggested in our troubleshooting guide. Power cycling or rebooting may sometimes solve complex technological problems. This is how to reboot your Netgear EX2700 WiFi range extender:
-
Turn off your extender and unplug anything linked to it.
-
Turn off the power to the Netgear EX2700 repeater entirely.
-
Give it some time to recuperate.
-
Reconnect the extender to a power source and activate it.
Check back later to check if the problem persists. If not, go on to the next piece of advice.
-
Inspect the Home Router
Dual-band networks are likely to be incompatible with your current WiFi router. If your home WiFi network only supports a 2.4 GHz connection, then you’ll need to pick the option to Use the 2.4 GHz WiFi band. Your range extender will then be able to actively monitor the 2.4 GHz frequency range.
-
Make Sure the Cables are Properly Connected
Verify that you have properly connected all of the cables used in the Netgear EX2700 range extender configuration. Any slack in the chain might cause a cascade of malfunctions and even prevent you from accessing the default IP 192.168.1.250 of the extender. Also, check the condition of each cable you want to utilize. There should never be a frayed wire. Immediately switch out the damaged cable with a new one if you discover any nicks or tears in it.
-
Verify DFS Streaming Channels
There is no way to use DFS channels with the Netgear EX2700 MU-MIMO range extender. It’s possible that your router is using a DFS channel if it’s compatible with them. That’s why the Netgear range extender can’t find your WiFi network during setup.
In this situation, a non-DFS 5 GHz channel must be selected for the router. When you are finished, go through the Netgear EX2700 setup procedure once again.
EndNote
Consequently, these are some of our preferred methods for resolving the EX2700 not detecting WiFi during the Netgear Genie setup process. In case you have any other suggestions for fixing this problem, please share them with the rest of us in the comments area.
